filename: tfs 1228a.doc version 1.3 27.06.2012 vectron international filter specification tfs 1228 a 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: input: 100 output: 100 characteristics remark: the maximum attenuation in the pass band is defined as the insertion loss a e . the nominal frequency f n is fixed at 1228.8 mhz without any tolerance or limit. the values of absolute attenuation a abs are guaranteed over the whole operating temperatur e range. the frequency shift of the filter within t he operating temperature range is included in the prod uction tolerance scheme. d a t a typ. value tolerance / limit insertion loss in pb a e 1.8 db max. 3.0 db nominal frequency f n 1228.8 mhz passband pb f n 12.5 mhz pass band variation 0.8 db max. 1.5 db absolute attenuation a abs 0.3 mhz ? 1152 mhz 34 db min. 30 db 1152 mhz ? 1191 mhz 35 db min. 20 db 1267 mhz ? 1306 mhz 42 db min. 20 db 1306 mhz ? 3000 mhz 34 db min. 30 db input power level in pb - max. 10 dbm operating temperature range otr - - 40 c ... + 85c storage temperature range - - 45 c ... + 85c temperature coefficient of frequency tc f * -46 ppm/k *) ? f c (hz) = tc f (ppm/k) x (t - t o ) x f cat (mhz) generated: checked / approved:
filename: tfs 1228a.doc version 1.3 27.06.2012 vectron international filter specification tfs 1228 a 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. filter characteristics construction and pin connection (all dimensions in mm) 1 2 3 5 6 7 4 8 1 ,0 +/-0,15 3 ,0 +/-0,15 0,6 +/-0,15 0,6 +/-0,15 0,6 +/-0,15 3 ,0 +/-0,15 6 0 1 3 7 5 date code 50 ohm test circuit 1 3 2, 4, 6, 8 saw 5 7 c28a c26 1 input 2 ground 3 input 4 ground 5 output 6 ground 7 output 8 ground date code: year + week c 2012 d 2013 e 2014 ... 500 1000 1500 2000 2500 3000 -60 -50 -40 -30 -20 -10 0 frequency in mhz magnitude in db 1180 1190 1200 1210 1220 1230 1240 1250 1260 1270 -70 -60 -50 -40 -30 -20 -10 0 frequency in mhz magnitude in db
filename: tfs 1228a.doc version 1.3 27.06.2012 vectron international filter specification tfs 1228 a 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plan, 3 pl ans; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; 5. esd ansi/esd s20.20-1999 , class 1a for hbm 6. moisture ipc/jedec j-std-20 msl classifications, msl 1 this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direction pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w : 8,00 0,3 po : 4,00 0,1 do : 1,50 +0,1/-0 e : 1,75 0,1 f : 3,50 0,05 g(min) : 0,75 p2 : 2,00 0,05 p1 : 4,00 0,1 d1(min) : 1,50 ao : 3,25 0,1 bo : 3,25 0,1 ct : 5,3 0,1 reel (all dimensions in mm) a : 180 w1 : 8,4 +1,5/-0 w2(max) : 14,4 n(min) : 60 c : 13,0 0,2
filename: tfs 1228a.doc version 1.3 27.06.2012 vectron international filter specification tfs 1228 a 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: tfs 1228a.doc version 1.3 27.06.2012 vectron international filter specification tfs 1228 a 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 generation of development specification. sch?nbein 08.06.12 1.1 update package drawing+ reliability requirement s sch?nbein 18.06.12 1.2 changed pinning back to spec version 1.0 sch?nbein 19.06.12 1.3 generation of filter specification s.springfeldt 27.06.12
|
